201安徽不銹鋼包口安裝費計算

　　201 Anhui stainless steel package installation fee calculation

　　一 計量口徑與工程量計算

　　Measurement caliber and engineering quantity calculation

　　計量單位以“米（m）”為主，按包口“中心線展開長度”計量；裝飾線條類通常按米計價與計量。若采用金屬板折邊做包口，也可按“平方米（m?）”計量，再折算為米用于安裝費核算。

　　The unit of measurement is mainly "meter (m)", measured according to the "centerline unfolded length" of the package; Decorative lines are usually priced and measured in meters. If metal sheet folding is used as the packaging, it can also be measured in square meters (m?) and converted into meters for installation cost accounting.

　　計算規則

　　calculation rule

　　直線段：按實際凈長計。

　　Straight line segment: calculated based on actual net length.

　　陽角/陰角：按“外包線長度”計（含包角展開），不重復計量直線段。

　　Positive/negative angle: calculated based on the "length of the outer edge" (including the unfolded edge), without repeating the measurement of straight line segments.

　　門套/門楣等：按可見外輪廓展開長度計。

　　Door frame/lintel, etc.: Calculated based on the visible outer contour unfolded length.

　　損耗：安裝費通常不計損耗，損耗體現在材料采購（常見按**3%–5%**計）。

　　Loss: Installation fees usually do not include loss, which is reflected in material procurement (usually calculated at * * 3% -5% * *).

　　示例

　　example

　　單開門包口：2（側邊）+（門楣長度）+（底邊長度）= 總安裝米數。

　　Single door package: 2 (side)+(lintel length)+(bottom edge length)=total installation meters.

　　陽角包邊：兩面外包線長度之和（含陽角折彎展開）。

　　External corner edge wrapping: the sum of the lengths of the external wrapping lines on both sides (including the bending and unfolding of the external corners).

　　以上口徑與計量做法與行業常見規則一致：裝飾線按米計算，包邊條在工廠可折彎加工，現場以米為安裝計量單位。

　　The above caliber and measurement methods are consistent with common industry rules: decorative lines are calculated in meters, edge banding can be bent and processed in the factory, and on-site installation measurement units are in meters.

　　二 單價構成與參考區間

　　Two unit price composition and reference range

　　安裝費通常拆分為：

　　The installation fee is usually divided into:

　　基層處理/找平（如需）

　　Grassroots treatment/leveling (if necessary)

　　定位放線、試拼、切割下料

　　Positioning and laying out, trial assembly, cutting and cutting of materials

　　粘貼/鉚接/焊接、打磨、清潔

　　Paste/rivet/weld, polish, clean

　　成品保護、垃圾清運、成品驗收

　　Finished product protection, garbage disposal, and finished product acceptance

　　市場常見參考價（僅指“安裝費”，不含材料、輔材、機械與成品保護等）

　　Common reference prices in the market (only referring to "installation fees", excluding materials, auxiliary materials, machinery, and finished product protection, etc.)

　　常規室內直線包邊：5–8 元/米（含粘接/打膠、常規切割與收口）

　　Regular indoor straight edge wrapping: 5-8 yuan/meter (including bonding/gluing, regular cutting and closing)

　　復雜部位（如大量陽角、弧線、燈槽、與石材/金屬/玻璃多材質交接）：在上述基礎上上浮 20%–50%

　　Complex parts (such as a large number of external corners, curved lines, lamp troughs, and intersections with multiple materials such as stone/metal/glass): increase by 20% -50% on the above basis

　　基層處理（如需）：

　　Grassroots treatment (if necessary):

　　磚墻基層：約 3.7 元/米·單/雙層50內

　　Brick wall base: about 3.7 yuan/meter, single/double layer within 50 yuan

　　夾板基層：約 2.5 元/米·單/雙層50內

　　Plywood base layer: about 2.5 yuan/meter, single/double layer within 50 yuan

　　每增加50 mm基層厚度：另加約 2 元/米

　　For every 50mm increase in base thickness, an additional fee of approximately 2 yuan per meter will be charged

　　計價口徑：按“安裝延長米”計，不隨板寬變化（10 cm 與 30 cm 包邊安裝工序差異已體現在單價中）。

　　Pricing caliber: Calculated based on "installation extension meters" and does not vary with the width of the board (the difference between the 10 cm and 30 cm edge wrapping installation processes has been reflected in the unit price).

　　以上區間與做法要點來源于行業報價與節點做法資料，適用于201不銹鋼包口的常見室內裝飾場景。

　　The above intervals and practice points are sourced from industry quotations and node practice data, and are applicable to common interior decoration scenarios with 201 stainless steel cladding.

　　三 快速報價公式與示例

　　Three Quick Quotation Formulas and Examples

　　公式

　　formula

　　安裝費合計 = Σ（各段“中心線展開長度” × 對應安裝單價） + 基層處理費 + 復雜節點上浮 + 其他費用（成品保護、清運等）

　　Total installation cost=∑ (length of each section's "centerline expansion" multiplied by the corresponding installation unit price)+base treatment fee+complex node uplift+other costs (finished product protection, cleaning, etc.)

　　示例（單開門包口，201不銹鋼，板寬100 mm，室內直線）

　　Example (Single door package, 201 stainless steel, plate width 100mm, indoor straight line)

　　假設：側邊各2.10 m，門楣1.00 m，底邊1.00 m，合計安裝米數 = 6.20 m

　　Assumption: 2.10m on each side, 1.00m on the lintel, and 1.00m on the bottom edge, with a total installation distance of 6.20m

　　安裝單價：6.0 元/米（取5–8元/米的中值）

　　Installation unit price: 6.0 yuan/meter (taking the median of 5-8 yuan/meter)

　　安裝費小計：6.20 × 6.0 = 37.20 元

　　Subtotal installation fee: 6.20 × 6.0=37.20 yuan

　　如需磚墻基層（單層50內）：3.7 × 6.20 = 22.94 元

　　If you need a brick wall base (within 50 units per layer): 3.7 × 6.20=22.94 yuan

　　合計：約 60.14 元（未含輔材如結構膠、保護、清運等，若含按合同口徑另計）

　　Total: Approximately 60.14 yuan (excluding auxiliary materials such as structural adhesive, protection, and transportation, if included, it will be calculated separately according to the contract scope)

　　該示例僅演示“按米計量、分部分項計價”的方法，復雜節點與基層條件按實際調整。

　　This example only demonstrates the method of "measuring by meter and pricing by sub item", and adjusts complex nodes and grassroots conditions according to actual conditions.

　　四 影響價格的關鍵因素與管控要點

　　Four key factors affecting prices and key control points

　　影響因素

　　influencing factors

　　基層狀況與找平難度（磚墻、夾板、是否需加襯板/龍骨）

　　Grassroots condition and leveling difficulty (brick walls, plywood, whether to add lining boards/keels)

　　線條寬度與折彎數量（陽角、陰角、弧線、多段拼接）

　　Line width and number of bends (male angle, female angle, arc, multi segment splicing)

　　工藝方式（膠粘、自攻螺絲/鉚接、焊接、背栓/卡槽等）

　　Process methods (adhesive, self tapping screws/riveting, welding, back bolt/slot, etc.)

　　收口與細節（與石材/木作/玻璃/金屬交接、縫隙控制、打磨拋光要求）

　　Closing and details (requirements for handover with stone/wood/glass/metal, gap control, and polishing)

　　現場條件（高空、狹小空間、成品保護難度、交叉作業）

　　Site conditions (high altitude, narrow space, difficulty in protecting finished products, cross operation)

　　質量要求（直線度、接縫順直、表面潔凈度、返工風險）

　　Quality requirements (straightness, straight seams, surface cleanliness, rework risk)

　　管控要點

　　Key Control Points

　　合同中明確：計量口徑（米/平方米）、單價包含/不包含的工作內容與輔材、基層處理責任與計價、復雜節點上浮比例、驗收標準與返工條款。

　　The contract specifies: measurement caliber (meters/square meter), work content and auxiliary materials included/excluded in the unit price, grassroots processing responsibilities and pricing, floating ratio of complex nodes, acceptance standards and rework clauses.

　　現場先試拼、統一下料尺寸，減少拼縫與打磨返工。

　　On site trial assembly and uniform cutting size to reduce joint and polishing rework.

　　對弧形/大尺寸包邊，優先工廠折彎，現場僅做定位與固定，降低誤差與工時。

　　For curved/large-sized edging, priority should be given to factory bending, and only positioning and fixing should be done on site to reduce errors and labor hours.

　　上述做法與注意點在行業節點與報價說明中被反復強調，尤其是“先打基底（最好有襯板）、工廠折彎、現場安裝”的流程與“計價按米、復雜上浮”的原則。

　　The above methods and precautions are repeatedly emphasized in industry nodes and quotation explanations, especially the process of "laying the foundation first (preferably with lining plates), factory bending, and on-site installation" and the principle of "pricing by meter and complex upward adjustment".

　　本文由  安徽不銹鋼包口   友情奉獻.更多有關的知識請點擊  http://www.jsnewc.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Anhui Stainless Steel Packaging For more related knowledge, please click http://www.jsnewc.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.